Lock Surgeon   Jobber   Supply

A Division of Lock Surgeon ™

Shipped Direct to You   or   In-Store Pick Up

Edmonton:
780-448-9243 Ext:4

Calgary:
403-770-5625 Ext:3

Toll Free:
1-844-448-9243 Ext:4

Adams Rite

Adams Rite Products
Back To Main Catagories

Adams Rite

Deadbolts, Deadlocks & Hookbolts

Adams Rite-Deadbolts-Deadlocks and Hookbolts

1850 SERIES MAXIMUM SECURITY LAMINATED DEADLOCKS/HOOKBOLTS
- Accepts standard mortise cylinder.
- Steel with corrosion resistant plating.
- Case size: 1” x 6".
- See page 5 for faceplates.
Backset - Finish
Long Throw Deadlock: 5/8” x 1-3/8” Throw
- 7/8” - Aluminum
- 1-1/2” - Aluminum
Long Throw Deadlock Less Faceplate: 5/8” x 1-3/8” Throw
- 31/32”
- 1-1/8”
Short Throw Deadlock: 5/8” x 13/16” Throw
- 31/32” - Aluminum
- 1-1/8” - Aluminum
Hookbolt: 5/8” x 13/16” Throw
- 7/8” - Aluminum
- 1-1/2” - Aluminum
Hookbolt Less Faceplate: 5/8” x 13/16” Throw
- 31/32”
- 1-1/8”

2190 SERIES DUAL FORCE® INTERCONNECTED DEADBOLT/DEADLATCH
- Interconnected deadbolt and deadlatch operate with a single motion release.
- Meets the most stringent building code egress requirements.
- Electrified lever option for access control.
- Re-handable.
- Clutched exterior lever trim..
- Passage mode lever sets available for interior doors
- FaceStyle adaptable faceplate system.
- Retrofits to MS® prepped doors.
- Key controlled extension of deadbolt and latch holdback.
- Positive latching for energy efficiency.
- ANSI/BHMA Type E82101 Grade 1.
Backset - Finish
With Trim Set
- 1-1/8” - Satin Stainless
With Electrified Trim Set
- 1-1/8” - Satin Stainless


Adams Rite

Deadlatches

Adams Rite-Deadlatches-4300 Series Steel Hawk-Electrified Latch-4513 Series Standard Duty Deadlatch

4900 SERIES HEAVY DUTY DEADLATCH
- Flexibility of traffic control and installation is offered by the 4900 series deadlatches.
- A reverse turn of the key while bolt is held retracted retains the bolt, to allow two-way traffic for applications which require free entrance at certain times and exit-only at other times.
- Interchangeable, without stile modification, with any MS1850A or MS1850S deadbolt of same backset and faceplate shape.
- etrofits to existing 4500/4700 deadlatch preparations; 1-3/4” minimum door thickness required.
- Cylinder backset: 31/32”, 1-1/8” or 1-1/2” only.
- Latch bolt: 5/8” x 1” x 5/8” throw, solid brass; handing is easily reversible using only a screwdriver.
- Auxiliary latch pin: Stainless steel; deadlocks latch bolt to prevent case-knife entry.
- Case: Steel with corrosion-resistant plating 7/8” x 5-13/16”.
- Screw-fastened tube spacer brackets allow for cleaner removal when tab mounting.
- Strikeplate: Standard strike furnished is 4902 for flat jamb where door closes flush or nearly flush.
- Faceplate: 1” x 6-7/8”, both flat and radius faceplates are supplied.
- Flat faceplates can also be adjusted in the field for right or left hand beveled edge doors.
- Retrofits: existing latch locks & 8400 series exit devices.
Backset - Finish
- 31/32” - Aluminum
- 1-1/8” - Duranodic
- 1-1/8” - Aluminum
- 1-1/2” - Aluminum

DEADLATCH PADDLES
- All paddles are reversible,
- Units for 4500/4700/4900 series latches include reversible cam disc.
Finish - Door - Thickness
Push to Left
- Duranodic - 1-3/4”
- Aluminum - 1-3/4”
- Aluminum - 2-1/4” to 2-1/2”
Ergonomic Style: Push to Left
- Duranodic - 1-3/4”
- Aluminum - 1-3/4”
Push to Right
- Duranodic - 1-3/4”
- Aluminum - 1-3/4”
Ergonomic Style: Push to Right
- Duranodic - 1-3/4”
- Aluminum - 1-3/4”
Ergonomic Style: Push to Left with Monitor Switch
- Aluminum - 1-3/4”


Adams Rite

Deadlatches & Paddles

Adams Rite-Deadlatches and Paddles-4900 Series Heavy Duty Deadlatch

LEVER HANDLES
Reversible 4580 Cam Disc:
- Included with 4560 & 4565 handles. Required to operate 4500/4700/4900 series latches.
Hand - Finish - Door Thickness
Operates with MS
- Rev - Aluminum - 1-3/4” to 2”
Operates with Deadlatch
- LH - Duranodic - 1-3/4” to 2”
- LH - Aluminum - 1-3/4” to 2”
- LH - Aluminum - 2-1/4” to 2-1/2”
- RH - Duranodic - 1-3/4” to 2”
- RH - Aluminum - 1-3/4” to 2”
- LH - Duranodic - 1-3/4” to 2”
- LH - Aluminum - 1-3/4” to 2”
- RH - Aluminum - 1-3/4” to 2”
- LH - Aluminum - 1-3/4” to 2”

4590 SERIES PADDLE & 4560 SERIES LEVER PARTS
Description- For
- Binder Post (Pk of 10) - Paddle
- Set Screw - Paddle
- Spring - Lever
- Spindle Assembly - Lever
- LH Cam Disc - Lever & Paddle
- RH Cam Disc - Lever & Paddle
- Spring Replacement Kit - Paddle

BOTTOM RAIL & DEADBOLT OPTIONS
MS1861:
- Utilizes the same over center/pivot locking mechanism as the MS deadlock. For use in the bottom rail of ultra-narrow stile doors and tempered glass doors (which have no stile at all). Use the 1830 when the bottom rail is too shallow to accommodate the MS1861.
MS4070:
- Offers the longest practical throw for a conventionally projected bolt from a narrow stile. Operates with one-half key turn of any standard mortise type cylinder or cylinder type thumbturn. NOT TO BE USED IN BOTTOM RAIL.
Backset - Description
- 31/32” - 5/8” Throw Bolt
- 1-1/8” - 5/8” Throw Bolt
- 2-1/4” - 13/16” Stainless Pin Bolt
- 31/32” - 5/8” Throw Horizontal Bolt
- 1-1/8” - 5/8” Throw Horizontal Bolt


Adams Rite

Lever Handles, Paddle and Lever Parts, Bottom Rail
& Deadbolt Options

Adams Rite-Lever Handles-Paddle and Lever Parts-Bottom Rail and Deadbolt Options

LEVER HANDLES
Reversible 4580 Cam Disc:
- Included with 4560 & 4565 handles. Required to operate 4500/4700/4900 series latches.
Hand - Finish - Door Thickness
Operates with MS
- Rev - Aluminum - 1-3/4” to 2”
Operates with Deadlatch
- LH - Duranodic - 1-3/4” to 2”
- LH - Aluminum - 1-3/4” to 2”
- LH - Aluminum - 2-1/4” to 2-1/2”
- RH - Duranodic - 1-3/4” to 2”
- RH - Aluminum - 1-3/4” to 2”
- LH - Duranodic - 1-3/4” to 2”
- LH - Aluminum - 1-3/4” to 2”
- RH - Aluminum - 1-3/4” to 2”
- LH - Aluminum - 1-3/4” to 2”

4590 SERIES PADDLE & 4560 SERIES LEVER PARTS
Description- For
- Binder Post (Pk of 10) - Paddle
- Set Screw - Paddle
- Spring - Lever
- Spindle Assembly - Lever
- LH Cam Disc - Lever & Paddle
- RH Cam Disc - Lever & Paddle
- Spring Replacement Kit - Paddle

BOTTOM RAIL & DEADBOLT OPTIONS
MS1861:
- Utilizes the same over center/pivot locking mechanism as the MS deadlock. For use in the bottom rail of ultra-narrow stile doors and tempered glass doors (which have no stile at all). Use the 1830 when the bottom rail is too shallow to accommodate the MS1861.
MS4070:
- Offers the longest practical throw for a conventionally projected bolt from a narrow stile. Operates with one-half key turn of any standard mortise type cylinder or cylinder type thumbturn. NOT TO BE USED IN BOTTOM RAIL.
Backset - Description
- 31/32” - 5/8” Throw Bolt
- 1-1/8” - 5/8” Throw Bolt
- 2-1/4” - 13/16” Stainless Pin Bolt
- 31/32” - 5/8” Throw Horizontal Bolt
- 1-1/8” - 5/8” Throw Horizontal Bolt


Adams Rite

MS Lock & Deadlatch Accessories

Adams Rite-MS Lock and Deadlatch Accessories

MS LOCK & DEADLATCH ACCESSORIES & PARTS
Description:
For MS & Latch
- Mounting Tabs
- Mounting Clip - Radius
- Mounting Clip - Flat
- Mounting Clip - Left Handed Bevel
- Mounting Clip - Right Handed Bevel
- 7/8” Set Screws
- 31/32” Set Screws
- 1-1/8” Set Screws
For Latch
- Long Box Strike For MS Replacement
- Strike Short Stainless Flat
- Standard Radius Double Door Strike
For MS Hook
- Box Strike For MS1850
For MS Flip
- Armoured Strike For MS1850

MS LOCK & DEADLATCH FACEPLATES
Type:
4710, 4513 (Measures 6-7/8” x 1”)
- Flat
- Flat
- Radius
- Left Handed Bevel
- Left Handed Bevel
- Right Handed Bevel
- Right Handed Bevel
- Radius With Weatherstrip
4720 (Measures 8” x 1-1/4”)
- Flat
- 4730, 4530 (Measures 7-13/32” x 1-1/4”)
- Flat
4900 (Measures 6-7/8” x 1”)
- Radius With Weatherstrip
MS1850 Series (Measures 6-7/8” x 1”)
- Flat
- Flat
- Radius
- Right Handed Bevel
- Radius With Weatherstrip


Adams Rite

Sliding Door, Keyless Entry Locks & Reinforcing Pivot

Adams Rite-Sliding Door-Keyless Entry Locks and Reinforcing Pivot

SLIDING DOOR LOCKS
MS1848 Deadlock
- For narrow stile sliding doors.
- Bolt: anti-lift/adjustable.
- Faceplate: Full radiused ends.
- Satin stainless finish.
- 2331 Deadlock For Heavy Sliding Doors.
- Backset: 1-3/4” only.
- Bolt: 1/2” x 1-1/2”.
- Strike: 1/8” x 1” x 4-11/16” with 5/8” x 1-5/8” opening.
- Faceplate: 1” x 5-3/4” flat.
Description - Case
- Patio Lock 1/2” x 3-3/16” x 1-1/8”
- Sliding Door Lock 7/8” x 3-5/8” x 2-11/16”

EFORCE KEYLESS ENTRY
- Keypad programmable unit has up to 150 users including master, supervisor, emergency users & 2 one time codes.
- For 1-3/4” to 2-1/4” thick left or right hand aluminum, steel & wood doors.
- Exterior locking trim.
- 31/32” backsets and greater.
- Non-handed.
- Three modes: Standard, operating & lockout.
- Free-wheeling lever with clutch.
- Powered by 4 AA batteries mounted in front cast housing.
- Device operation is confirmed by both a visual LED light indicator and an audible sound generated by a piezo horn.
- Measures: 1-3/4”W x 15-3/8”H.
- Temperature range: -35°C to +66°C.
Finish
- For 4500, 5700, 4900 Latches & 8000 Series Exit Devices
- Duranodic
- Satin Chrome

FULL SURFACE REINFORCING PIVOT
- Full-surface reinforcing pivot for flush doors.
- Adds years of life to openings where the hinges or hinge reinforcements have failed.
- An economical way to solve door sag problems by taking the load off the top hinge and transfer it to screws that are in shear so they will not pull out.
- Designed with a 1/2” offset to match the pivot point of a 4” wide butt hinge.
- Zinc plated over steel finish.
- Heavy-duty 3/16” cold-rolled steel.
- Supports weights up to 300 lbs.
Description
- 4” Hinge Application


Adams Rite

Exit Devices & Parts

Adams Rite-Exit Devices and Parts-8000 Series Exit Device Parts

EXIT DEVICES
- UL life-safety listed, ANSI/BHMA A153.6 Grade 1.
8099 Active Dummy Bar with Switch
- Can be wired normally open or normally closed to operate maglock, alarm, etc.
- No latching mechanism.
8211 Surface Vertical Rod
- For 1-3/4” thick narrow stile glass/aluminum doors with widths of 30” to 36” and heights up to 8’.
- Requires 2” stile minimum.
- Will accept optional rim cylinder.
- Patented top latching mechanism interlocks door to frame.
- Adjustable rods encased in contoured covers.
8400 Mortise Exit Device
- Fits single leaf aluminum stile glass door, standard narrow stile cutout.
- 5/8” bolt throw.
- Minimum stile width is 2”.
- Strike for installations where 1-3/4” door closes flush with jamb.
- Push bars are extruded anodized aluminum with black ABS end cap.
- Handing can be reversed.
Finish - Backset - Hand
- Aluminum — —
- Aluminum — —
- Aluminum - 31/32" - RHR
- Aluminum - 1-1/8" - RHR

8000 SERIES EXIT DEVICE PARTS
Description
- For 8800 Series
- Old Style Dogging Key
- New Style Dogging Key
- Active End Cap
- For 8200 & 8800 Series
- Dogging Assembly
- For 8400 Series
- Active End Cap
- 2-1/2” Thick Door Kit