Lock Surgeon   Jobber   Supply

A Division of Lock Surgeon ™

Shipped Direct to You   or   In-Store Pick Up

Edmonton:
780-448-9243 Ext:4

Calgary:
403-770-5625 Ext:3

Toll Free:
1-844-448-9243 Ext:4

Commercial Door Closers

LCN 1461 Commercial Door Closer
Back To Main Catagories

Dorma

Door Closers

TS77 SUITE ENTRANCE DOOR CLOSER
- The low cost solution for suite entrance & low traffic doors.
- Non-handed.
- Quick and easy to install.
- Mounts without a mounting backplate.
- Compact design.
- Inexpensive, proven reliability.
- Stocked in aluminum.

RTS88 OVERHEAD CONCEALED DOOR CLOSER
- Concealed Body Only, Non-Hold Open
- Side Load Arm - End Load Arm - Side Load Arm
- For wood, aluminum, or hollow metal doors.
- Single and double-acting non hold open with latch & sweep valves with pressure relief valve.
- Fits into a 1-3/4" x 4" header.
- 105º maximum opening door swing.
- For doors up to 250 pounds with a maximum 3'-6" width exterior, & 4’ interior.
- Arm must be purchased seperately - it is not included with the body only package.
- 8831 Side Load Arm - Requires 1/2” top rail channel depth.
- 8836 End Load Arm - Requires 7/8” top rail channel depth.

7400 SERIES HYDRAULIC SURFACE APPLIED RACK AND PINION CLOSER
- It meets 5 lbs interior barrier-free applications.
- Non-handed for regular, top jamb and parallel arm applications.
- ANSI A156.4 Grade 1.
- UL & cUL listed for UL10C and UBC 7.2 for positive pressure.
- Two noncritical adjusting valves (sweep and latch) with thermostatic properties work to provide consistent closing speeds under a wide variety of temperatures.
- Adjustable backcheck standard. Provides cushioning when the door is abusively opened.
- BP640C mounting bracket can be used when installing into a 9-1/16” template åhole pattern.


Dorma

Floor Closers & Door Holders

BTS80 FLOOR CLOSER
- Replacement body is 13-7/16"L x 2-3/8"D.
- Cover not included.
- Mechanical backcheck at approximately 70º.
- Selectable delayed action between 175º and 75º.
- Delayed action is functional when hold open is not engaged.
- Selectable multipoint hold open between approximately 75º and 175º.
- Adjustment for hold open between 75º and 105º.
- Accommodates doors weighing up to 660 pounds and 4'-6" wide interior and 4'-0" exterior.
- Closer adjustment in cement case provides lateral and longitudinal adjustment of BTS80 1/4" and height adjustment of 5/32".
- Long Catch or Short Catch.

ELECTROMAGNETIC DOOR HOLDER
- Dual voltage capability reduces stocking requirements.
- Low current draw allows savings on power supplies and backup batteries.
- Optional extension rods fit on standard catch plate to accommodate deeper door to wall conditions.
- Low residual magnetism allows easy release of door.
- All electrical values +10% to –15%.
- Floor & wall mounted styles.
- Can be manually pulled from hold open position.
- Silent operation.
- Holding force 15–25 lbs nominal.
- Can be manually pulled from hold open position with 25-40 maximum hold open force.
- Voltage: 24 VAC/DC or 120 VAC.
- Amps: .015.
- Meets ADA requirements with minimal spring force door closers.
- ANSI A156.15 Grade 1.
- UL and cUL listed.
- Finish: Satin chrome.

EM504
- Semi flush wall mount.
- Overall projection: 3-1/2”.

EM508
- Surface wall mount.
- Overall projection: 4-1/16”.


Falcon

Automatic Operator

8200 SERIES AUTOMATIC OPERATOR
- Push Arm door operator with Pull Arm capability (Pull Arm option requires Pull Arm Kit).
- Versatile and easily integrated into electrified openings with wireless accessories: Call us for details.
- Designed to fit in low to moderate traffic applications, such as assisted living, ambulatory care, hospitality, retail, restaurant and small office where ease of use is critical.
- Slim & sleek profile has a smaller footprint for clean lines and an attractive look.
- Ensures smooth, convenient door opening for areas requiring easy accessible and ADA compliance.
- Provides dependable performance at an affordable price point.
- Aluminum powder coated steel cover.
- Mounting bracket contains fastening notches to reduce parts and allow for faster and easier installation.
- One-piece mounting bracket eliminates the need for end caps, reducing parts and installation time.
- Non-handed motor gearbox uses mechanical controls to act as a size 3 door closer in manual operation.
- Intelligent control box provides the most precise door operation and includes adjustable features for all commercial applications.
- Steel aluminum finished cover makes the 8200 Series aesthetically pleasing for any application.
- Push Arm Door Operator w/ Pull Arm Capability Options: Replacement Push Arm — Pull Arm Kit (Pull Arm with Track).

Standard Features That You Can Use To Customize Every Opening:
- Smart Latch: Senses and overcomes external pressure conditions with a graduated energy assist for secure latching.
- Push’n’Go: Selectable feature allows door to open automatically as soon as it feels pressure.
- Open Position Learning: Automatically sets the opening position to eliminate wall and door damage.
- Obstacle Obstruction Detection: Safety feature stops and reverses door direction when distress or an obstruction is sensed.
- Pre-Load Strike Assist: Removes load on strike lip with a one second delay allowing the door to release and automatically open.
- LED Light Illumination: Light illumination on control box signals accurate installation and helps with connection diagnostics.
- On Board Power Supply (12 VAC): Powers accessories and actuators, power supply may be required for a separate locking device.

Adjustable Features:
- Hold-open time delay; 0-15 seconds.
- Backcheck position.
- Backcheck speed.
- Opening/closing speed.

Specifications:
- Electro-hydraulic single door operation.
- Surface top jamb mount.
- Header length: 26”.
- Reduced force.
- Low energy.
- Cycle tested - 1 million gear box.
- Electric strike replay included.
- Non-handed.
- Max door weight: 200 pounds.
- Stocked with Push Arm.


Falcon

Light Duty & Slim Door Closers

GRADE 1 DOOR CLOSERS
- ANSI/BHMA A156.4, Grade 1 certified.
- UL10C approved all weather fluid, UBC 7-2 (1997) fire test.
- Closer mounts hinge side, top jamb or parallel arm.
- Single piece cast aluminum body.
- 1-3/8” diameter piston.
- Staked valves.
- Separate adjustable general speed, latch speed and backcheck.
- Heat-treated steel pinion.
- Universal screw pack.
- Suitable for interior doors from 30” to 54” wide and exterior doors up to 42” wide.
- For hinge side, top jamb or parallel arm applications.
- Single piece cast aluminum body with adjustable speed, latch speed & backcheck.
- Fits standard Norton 9-1/16” hole spacing.
- Non-handed.

GRADE 1 SLIM DOOR CLOSERS
- Meets ANSI A117.1.
- ANSI/BHMA A156.4, grade 1.
- 1-1⁄4“ diameter piston.
- Closer mounts hinge side, top jamb or parallel arm.
- Single piece cast aluminum body.
- Non-handed for left or right swinging doors.
- Separate adjustable general speed, latch speed and backcheck.
- Heat-treated steel piston.
- Heat-treated pinion.
- Universal screw pack for aluminum, hollow metal, and wood doors.
- Non-handed.

LIGHT DUTY INTERIOR DOOR CLOSER
- ANSI A156.4, Grade 3.
- UL10C approved all weather fluid, UBC 7-2 (1997) fire test.
- Closer mounts hinges side, top jamb or parallel arm.
- Single piece cast aluminum body.
- Separate adjustable general speed and latch speed & backcheck.
- Heat-treated steel piston.
- Heat-treated pinion.
- Handicap compliant.
- No backcheck.
- Non-handed.


Glynn-Johnson

Door Holders & Door Stops

HEAVY DUTY DOOR HOLDERS & STOPS
- For heavy-duty applications.
- Non-handed.
- 900 series: Channel is surface-mounted to the door, most often with sex bolts, and the jamb bracket is surface mounted to the jamb, requiring minimal door and frame preparation.
- Can be used in conjunction with most surface-applied door closers.
- Can be mounted for openings ranging from 85º to 110º.

Hold-Open Function
- Holds the door open at a predetermined position permitting an unobstructed traffic flow through the opening.
- Can easily be turned on or off by simply rotating the serrated knob on the bottom of the channel to engage the hold open mechanism, when flipped over it acts as a stop and shock absorber.
- Tension on the hold-open mechanism can be adjusted to offset air currents or other exterior conditions.

Stop Function
- Provides a reliable method for shock absorbing capability.
- Can be used on fire doors.

Surface Mount: Stop Only
- 27-1/16”–33” 33-1/16”–39”.
- 33-1/16”–39” 39-1/16”–45”.

Surface Mount: Hold Open
- 33-1/16”–39” 39-1/16”–45”.

Concealed Mount: Stop Only
- 33-1/16”–39” 45-1/16”–51”.

DOOR STOP Kick Down Holder
- Units provide an economical method to hold open doors.
- Cast of durable iron.
- Non-marring rubber shoes have corrugated bottoms to provide secure grip; rubber shoe is securely fastened with screw, shoes are easily replaced when worn.
- Door-to-floor clearance: 2” or less.
- Plate height: 2-1/4”.
- Plate width: 1-7/16”.
- Meets ANSI/BHMA 156.16, L11381.
- Kick Down Door Stop.
- Screw Type Replacement Heel.


LCN

1260 Series Adjustable & 1460 Series Commercial Closers

1260 SERIES MODERATE TRAFFIC ADJUSTABLE CLOSERS
- The 1260 series combines the best features from the previous 1070 and 1370 into a single versatile and economical cast iron closer, with dual mounting capability.
- Adjustable from size 1 to 5 for interior doors up to 4’6” doors and exterior doors up to 3’6” doors.
- Closer mounts hinge side, top jamb and parallel arm on either right or left swinging doors.
- Aluminum powder coat finish.
- Cast iron cylinder.
- Peel and stick template.
- Hold Open, Standard or Slim Plastic.

1460 SERIES COMMERCIAL & INSTITUTIONAL CLOSERS
- Designed for maximum versatility, the 1460 can be used for both commercial and institutional applications.
- This fully universal closer offers a wide variety of options and fast and accurate installation.
- Adjustable from size 1 to 6 for interior 5’ doors and up to 4’ for exterior doors.
- Closer mounts hinge side, top jamb and parallel arm on either right or left swinging doors.
- Powder coat finish.
- Supplied with slim line cover.

1461RW/PA DEL TBSRT ALUM - Delayed Action
- Delays closing from 120° to 70°.
- Delay time adjustable up to approximately 1 minute.
- Standard, Cush or Hold Open.


LCN

3133 Series Concealed, 4010 Series Pull Side
& 4020 Series Push Side Closers

3133 SERIES CONCEALED DOOR CLOSERS
- Designed to mount in a 1-3/4” interior door
- The single lever arm and roller assembly provides complete concealment and the choice of finishes and track functions meet virtually all architectural requirements.
- Standard 3130 series closer shipped with standard arm, standard track and wood and machine screw pack.
- Sized cylinders for interior doors to 3’2”.
- Handed for right or left swinging doors.
- Closers to meet ADA requirements.
- Standard or optional custom powder coated finish.
- Optional plated finish on arm and fasteners.
- Optional SRI primer for installations in corrosive conditions.
- Consult factory for installation with pivots.
- Left or Right Hand.

4010 SERIES SMOOTHEE® HINGE (PULL SIDE) MOUNTING CLOSERS
- The best performing heavy duty closer for institutional and other high traffic applications.
- Adjustable from size 1 to 5 for interior doors up to 4’6” and exterior doors from size 3 to 5 up to 3’6”.
- Closer mounts hinge side, specify left or right swing doors.
- All weather fluid.
- Peel and stick template.
- Cast iron cylinder meets ADA requirements.
- Capable of ten million cycles.
- Forged steel main arm.
- Double heat treated steel pinion.
- ANSI standard A156.4 Grade 1 certified.
- UL listed for self-closing doors without hold-open.
- Left or Right Hand.

4020 SERIES SMOOTHEE® TOP JAMB (PUSH SIDE) MOUNTING CLOSERS
- The best performing heavy duty closer for institutional and other high traffic applications.
- Adjustable from size 1 to 5 for interior doors to 4’6” and exterior doors to 3’6”.
- Closer mounts top jamb (push side), specify right or left swinging door.
- All weather fluid.
- Peel and stick template.
- Cast iron cylinder meets ADA requirements.
- Capable of ten million cycles.
- Forged steel main arm.
- Double heat treated steel pinion.
- ANSI standard A156.4 Grade 1 certified.
- UL and cUL listed with regular or fusible link arms for self-closing doors.
- Left or Right Hand.


LCN

4030 Series Universal & 4040 SE Series Sentronic Closers

4030 SERIES CAST IRON UNIVERSAL CLOSER
- A cast iron, universal closer designed specifically for doors in moderate traffic conditions.
- Standard new 4030 series closer is shipped with forged regular arm, metal cover and wood/self-tapping machine screw pack.
- Non-sized 4031 cylinder is adjustable from sizes 1 to 4 for exterior doors to 36” (914mm) and interior doors to 48” (1219mm).
- Closer mounts hinge side, top jamb, and parallel arm, on either right or left swinging doors.
- Closer meets ADA requirements.
- Cast Iron.
- Forged steel main arm.
- Heat treated steel pinion.
- All weather fluid reduces seasonal adjustments.
- UL and cUL listed for self-closing doors without hold-open.
- ANSI Standard A156.4, grade 1 certified.

4040SE SENTRONIC® CLOSERS
- Provides single point hold-open for fire and smoke barrier doors.
- Door is held open until current interruption releases the holding mechanism and the door closes.
- Single lever track arm closer is specifically designed for interior doors.
- Available 24VDC or 120VAC.
- Non-sized for interior doors up to 4’0”.
- Hold-open force is adjustable between 85° to 110° in approximately 3° increments (push side) and maximum to 95° (pull side).
- Momentary on/off switch board assembly for testing door release also provides over-voltage protection.
- Functions as a full rack and pinion closer when hold-open is not engaged or current is interrupted.
- Closer mounts on either push or pull side of the door.
- Interfaces with fire alarm systems.
- UL listed for smoke barrier or labeled fire doors.
- cUL listed for self-closing doors without hold-open.
- Tested and certified under ANSI Standard A156.15.
- Conforms to life safety code, NFPA 101.


LCN

Heavy Duty 4040XP Series Mounting Brackets

4040XP SERIES ADJUSTABLE CLOSER
- 4040XP DELRW/PA TBSRT - Delayed Action
- Delays closing from 120° to 70°.
- Delay time adjustable up to approximately 1 minute.
- The smoothest durable heavy duty, double lever arm closer for the most demanding, high use and abuse applications.
- Strongest pinion at 3/4” journal diameter, widest bearing at 5/8”, stronger pinion teeth, V-shield™ seal with 20% longer life than conventional seals, 44% increased bearing load capacity.
- Adjustable from size 1 to 6 for interior doors up to 5’0” and exterior doors up to 4’0” using the Fast™ power adjust feature.
- Closer mounts hinge side, top jamb, and parallel arm.
- Cast iron cylinder.
- Non-handed.
- Meet handicap standards for reduced opening force.
- Capable of ten million cycles.
- Cast iron forged steel arm.
- Double heat treated steel pinion.
- All weather fluid.
- Powder coat finish.
- Cush, Standard, Extra Duty, Hold Open, Hold Open Cush, Spring Cush, Hold Open Spring Cush.

4040 MOUNTING BRACKETS 4040 18
- Required for hinge side mount where top rail is less than 3-3/4”. 4040 18G
- Locates top jamb mounted closer flush with top of head frame face in flush ceiling condition.
- Plate requires 1-3/4” minimum head frame. 4040 18PA
- Required for parallel arm mounting where top rail is less than 5-1/2” measured from the stop.
- Plate requires 2” minimum top rail. 4040 18TJ
- Centers top jamb mounted closer vertically on head frame where face is less than 3-1/2”.
- Plate requires 1-3/4” minimum head frame.
- Drop Plate, Flush Drop Plate, Parallel Arm Plate, Top Jamb Plate.


LCN

4040XP Arm Options & 4110 Series Push Side Closer

4040XP SERIES ARM OPTIONS Standard (Regular) Arm
- Non-handed arm mounts pull side or top jamb with shallow reveal. Cush Arm
- Optional, non-handed parallel arm features solid forged steel main arm and forearm with stop in soffit shoe. Spring Cush Arm
- Optional, non-handed parallel arm for abusive applications features solid forged steel main arm and forearm with spring loaded stop in the soffit shoe.
EDA - Extra Duty Arm
- Non-handed parallel arm features forged, solid steel main and forearm for potentially abusive installations.
H - Hold Open Arm
- Optional, non-handed arm mounts pull side or top jamb with shallow reveal, hold open, adjustable shoe.
Hold Open cush
- Provides hold-open function with templated stop/hold-open points.
- Handle controls hold-open function.
Hold Open Spring Cush
- Optional, non-handed parallel arm for abusive applications features solid forged steel main arm and forearm with spring loaded stop in the soffit shoe.
- Handle controls hold-open function.
- 4040 79 - Rod & Shoe.
- 4040 79LR - Long Rod & Shoe.
- 4040 3077 - Standard Arm.
- 4040 3049 - Hold Open Arm.
- Spring Cush Arm, EDA Arm, Cush Arm, Hold Open Cush, Hold Open Spring Cush.

4110 SERIES SMOOTHEE® (PUSH SIDE) ADJUSTABLE CLOSERS
- The best performing heavy duty closer for institutional and other high traffic applications.
- 4111 is adjustable from size 2 to 5 for interior 5’ doors and exterior from size 3 to 5 for up to 4’ doors.
- 4114 is for exterior doors 30-36”, and interior doors 38-48”.
- Closer mounts parallel arm, select right or left.
- All weather fluid reduces seasonal adjustments.
- Aluminum powder coat finish.
- Cast iron cylinder.
- Meets handicap standards for reduced opening force.
- Peel and stick template.
- Capable of ten million cycles.
- Forged steel arm.
- Double heat treated steel pinion.
- Extra Duty LH/RH.
- Adjustable Hold Open Cush LH/RH.
- Adjustable Spring Cush LH/RH.


LCN

Auto Equalizer Pneumatic & Benchmark Low Energy Operators

4822 SERIES AUTO EQUALIZER™ PNEUMATIC OPERATOR
- This low energy automatic operator provides easy access for people with disabilities, the elderly, or the frail.
- Designed primarily for manual opening applications that occasionally require automatic opening.
- Size 2 push side pneumatic auto equalizer.
- Packed with thru bolts, wood & machine screws.
- Ideal for multi-door applications since cost per door leaf decrease significantly as the number of door leaves increases.
- Utilizes a 10,000,000 cycle heavy duty door closer.
- Quiet, efficient & reliable.
- Requires control boxes with integral compressor or control box using auxiliary air supply.
- No guard rails/safety mats required.
- Meets ADA requirements (power mode).
- Non-sized cylinders for interior doors to 4’6” and exterior doors to 3’6”.
- Non-handed.
- UL listed 228 and meets the provisions of ANSI Standards A117.1, A156.19, and the Americans with Disabilities Act.
- Reveal of 4-1/2” allows up to 90° power opening and 100° manual opening.
- Head frame minimum: 1-3/4”.
- Top rail minimum: 1-3/4”.
- Push Side.

9130 SERIES BENCHMARK LOW ENERGY OPERATOR
- Non-handed for either right or left swinging door.
- Designed primarily for automatic opening applications that occasionally require manual opening.
- Operator is shipped with motor gearbox, control box, mounting plate, standard arm, metal cover, standard track, wood and machine screws.
- On/Off switch included as standard.
- 36” cover is standard.
- Fits doors 30” to 36” width.
- All potentiometers clearly labeled with their functions.
- LED lights indicate power to control box and motor gearbox.
- Push-‘n-go permits non-switch activation.
- Tested internally to over 3,000,000 cycles.
- Power Boost allows for increased closing force near latch position.
- 9-3/4” for optional long arm; reveal should not exceed 1/8” on pull installations.
- Head frame minimum 2”.
- Top rail minimum 2” - flush ceiling installation requires 5-1/4” minimum.
- Opening and closing time are variable by adjustments to the electronic control module located on the operator assembly - maximum hold open time adjustable up to approximately 30 seconds.
- Template allows 90° power opening and 90° manual opening.
- Pull Side.


Sargent

Mullion & Door Closers

REMOVABLE MULLION
- For double door applications without existing mullion.
- T-shaped: 2-1/2” x 3”.
- Stock size: 96” long, maximum length 102”.
- Weight: 18 lbs.
- Finish: Aluminum prime coat.
- Includes top retainer - 511 & bottom retainer - 502.
- Non-handed.
- Removable Aluminum Mullion.

351 & 1431 SERIES DOOR CLOSERS
- ANSI/BHMA A156.4 Grade 1.
- Conforms to UL10C and UBC for positive pressure fire test.
- cUL listed to Canadian safety standards listed for use on fire doors.
- For interior and exterior applications.
- High impact non-corrosive plastic covers standard.
- Adjustable from size 1 to 6.
- Complies with handicap regulations for reduced open force.
- Non-handed.
- Meets ADA requirements.
- All weather capabilities.
- Universal arm package provides brackets and arms to install closer in standard top jamb or parallel applications.
- MicroShield® technology: A silver-based antimicrobial coating designed to inhibit the growth of bacteria.
351
- Case size: 13”W x 3-7/8”H.
- Maximum reveal: 7/16”.
- Powerglide® line of surface door closers has been engineered to meet the demands of architects and building owners.
- Ideally suited for exterior doors in heavy draft and wind conditions.
- Rack & pinion for better control.
- Heavy duty one piece die cast aluminum silicon alloy body with 14% silicon provides superior strength and wear resistance.
1431
- Case size: 12”W x 3-3/8”H.
- General purpose quality grade closer.
- Retrofits discontinued 1230/ 1231 models.
- Constructed from a carefully selected aluminum silicon alloy to accommodate the door closer characteristics increasing the body strength and wear resistance.
- Key control valves offer separate regulating for door speed, latching & backcheck.