Lock Surgeon   Jobber   Supply

A Division of Lock Surgeon ™

Shipped Direct to You   or   In-Store Pick Up

Edmonton:
780-448-9243 Ext:4

Calgary:
403-770-5625 Ext:3

Toll Free:
1-844-448-9243 Ext:4

Glass Aluminum Door Lock Parts

Glass Aluminum Door Parts-Adams Rite-Keedex-MajorMFG
Back To Main Catagories

Adams Rite

Deadbolts, Deadlocks & Hookbolts

Glass-Aluminum-Adams Rite-Deadbolts-Deadlocks and Hookbolts

1850 SERIES MAXIMUM SECURITY LAMINATED DEADLOCKS/HOOKBOLTS
- Accepts standard mortise cylinder.
- Steel with corrosion resistant plating.
- Case size: 1” x 6".
- See page 5 for faceplates.
Backset - Finish
Long Throw Deadlock: 5/8” x 1-3/8” Throw
- 7/8” - Aluminum
- 1-1/2” - Aluminum
Long Throw Deadlock Less Faceplate: 5/8” x 1-3/8” Throw
- 31/32”
- 1-1/8”
Short Throw Deadlock: 5/8” x 13/16” Throw
- 31/32” - Aluminum
- 1-1/8” - Aluminum
Hookbolt: 5/8” x 13/16” Throw
- 7/8” - Aluminum
- 1-1/2” - Aluminum
Hookbolt Less Faceplate: 5/8” x 13/16” Throw
- 31/32”
- 1-1/8”

2190 SERIES DUAL FORCE® INTERCONNECTED DEADBOLT/DEADLATCH
- Interconnected deadbolt and deadlatch operate with a single motion release.
- Meets the most stringent building code egress requirements.
- Electrified lever option for access control.
- Re-handable.
- Clutched exterior lever trim..
- Passage mode lever sets available for interior doors
- FaceStyle adaptable faceplate system.
- Retrofits to MS® prepped doors.
- Key controlled extension of deadbolt and latch holdback.
- Positive latching for energy efficiency.
- ANSI/BHMA Type E82101 Grade 1.
Backset - Finish
With Trim Set
- 1-1/8” - Satin Stainless
With Electrified Trim Set
- 1-1/8” - Satin Stainless


Adams Rite

Deadlatches

Glass-Aluminum-Adams Rite-Deadlatches-Steel Hawk 4300-4513 Series Standard Duty Deadlatch

THE STEEL HAWK 4300 ELECTRIFIED LATCH
- The easiest way to electrify an aluminum entrance door.
- Non-handed right out of the box due to it’s patented two-way winged technology.
- Interfaces with existing Adams Rite handles, paddles and the new 4600 designer series handles.
- Adapts to 12, 16, 24 VDC.
- All steel construction with stainless steel latchbolts.
- Retrofits to MS® prep.
- Direct replacement for 4900/4500/4700 deadlatches using the same strike.
- Optional locked/unlocked status monitor switch.
- All steel construction with stainless steel latchbolts.
- WHI listed, UL 1034.
- Exceeds ANSI/BHMA Grade 1 requirements.
Backset
- 31/32”
- 1-1/8”

4513 SERIES STANDARD DUTY DEADLATCH
- Cylinder backset: 7/8”, 31/32”, 1-1/8” (or 1-1/2” by special order).
- Case: steel with corrosion-resistant plating 1“ x 5-13/16” x depth.
- Flexibility of traffic control during and after business hours; a reverse turn of the key while bolt is held retracted retains the bolt, to allow two-way traffic for hospitals, banks, stores and other buildings which require free entrance at certain times and exit-only at other times.
- Interchangeable, without stile modification, with any MS1850A or MS1850S deadbolt of same backset and faceplate shape (They do not, however, provide the same maximum security level as the MS® deadbolt).
- Latch bolt: 1/2“ x 1” x 1/2” throw, all metal with hardened steel internal pins.
- Handing is reversible without special tools.
- Auxiliary bolt: All metal, deadlocks latch bolt to prevent case-knife entry.
- Stocked less faceplate.
Backset - Hand
- 7/8” Left
- 31/32” - Left
- 31/32” - Right
- 1-1/8” - Left
- 1-1/8” - Right


Adams Rite

Deadlatches & Paddles

Glass-Aluminum-Adams Rite-Deadlatches and Paddles-4900Series Heavy Duty Deadlatch

4900 SERIES HEAVY DUTY DEADLATCH
- Flexibility of traffic control and installation is offered by the 4900 series deadlatches.
- A reverse turn of the key while bolt is held retracted retains the bolt, to allow two-way traffic for applications which require free entrance at certain times and exit-only at other times.
- Interchangeable, without stile modification, with any MS1850A or MS1850S deadbolt of same backset and faceplate shape.
- etrofits to existing 4500/4700 deadlatch preparations; 1-3/4” minimum door thickness required.
- Cylinder backset: 31/32”, 1-1/8” or 1-1/2” only.
- Latch bolt: 5/8” x 1” x 5/8” throw, solid brass; handing is easily reversible using only a screwdriver.
- Auxiliary latch pin: Stainless steel; deadlocks latch bolt to prevent case-knife entry.
- Case: Steel with corrosion-resistant plating 7/8” x 5-13/16”.
- Screw-fastened tube spacer brackets allow for cleaner removal when tab mounting.
- Strikeplate: Standard strike furnished is 4902 for flat jamb where door closes flush or nearly flush.
- Faceplate: 1” x 6-7/8”, both flat and radius faceplates are supplied.
- Flat faceplates can also be adjusted in the field for right or left hand beveled edge doors.
- Retrofits: existing latch locks & 8400 series exit devices.
Backset - Finish
- 31/32” - Aluminum
- 1-1/8” - Duranodic
- 1-1/8” - Aluminum
- 1-1/2” - Aluminum

DEADLATCH PADDLES
- All paddles are reversible,
- Units for 4500/4700/4900 series latches include reversible cam disc.
Finish - Door - Thickness
Push to Left
- Duranodic - 1-3/4”
- Aluminum - 1-3/4”
- Aluminum - 2-1/4” to 2-1/2”
Ergonomic Style: Push to Left
- Duranodic - 1-3/4”
- Aluminum - 1-3/4”
Push to Right
- Duranodic - 1-3/4”
- Aluminum - 1-3/4”
Ergonomic Style: Push to Right
- Duranodic - 1-3/4”
- Aluminum - 1-3/4”
Ergonomic Style: Push to Left with Monitor Switch
- Aluminum - 1-3/4”


Adams Rite

Lever Handles, Paddle and Lever Parts, Bottom Rail
& Deadbolts Options

Glass-Aluminum-Adams Rite-Lever Handles-Paddle and Lever Parts-Bottom Rail and Deadbolts

LEVER HANDLES
Reversible 4580 Cam Disc:
- Included with 4560 & 4565 handles. Required to operate 4500/4700/4900 series latches.
Hand - Finish - Door Thickness
Operates with MS
- Rev - Aluminum - 1-3/4” to 2”
Operates with Deadlatch
- LH - Duranodic - 1-3/4” to 2”
- LH - Aluminum - 1-3/4” to 2”
- LH - Aluminum - 2-1/4” to 2-1/2”
- RH - Duranodic - 1-3/4” to 2”
- RH - Aluminum - 1-3/4” to 2”
- LH - Duranodic - 1-3/4” to 2”
- LH - Aluminum - 1-3/4” to 2”
- RH - Aluminum - 1-3/4” to 2”
- LH - Aluminum - 1-3/4” to 2”

4590 SERIES PADDLE & 4560 SERIES LEVER PARTS
Description- For
- Binder Post (Pk of 10) - Paddle
- Set Screw - Paddle
- Spring - Lever
- Spindle Assembly - Lever
- LH Cam Disc - Lever & Paddle
- RH Cam Disc - Lever & Paddle
- Spring Replacement Kit - Paddle

BOTTOM RAIL & DEADBOLT OPTIONS
MS1861:
- Utilizes the same over center/pivot locking mechanism as the MS deadlock. For use in the bottom rail of ultra-narrow stile doors and tempered glass doors (which have no stile at all). Use the 1830 when the bottom rail is too shallow to accommodate the MS1861.
MS4070:
- Offers the longest practical throw for a conventionally projected bolt from a narrow stile. Operates with one-half key turn of any standard mortise type cylinder or cylinder type thumbturn. NOT TO BE USED IN BOTTOM RAIL.
Backset - Description
- 31/32” - 5/8” Throw Bolt
- 1-1/8” - 5/8” Throw Bolt
- 2-1/4” - 13/16” Stainless Pin Bolt
- 31/32” - 5/8” Throw Horizontal Bolt
- 1-1/8” - 5/8” Throw Horizontal Bolt


Adams Rite

MS Lock & Deadlatch Accessories

Glass-Aluminum-Adams Rite-MS Lock and Deadlatch Accessories

MS LOCK & DEADLATCH ACCESSORIES & PARTS
Description:
For MS & Latch
- Mounting Tabs
- Mounting Clip - Radius
- Mounting Clip - Flat
- Mounting Clip - Left Handed Bevel
- Mounting Clip - Right Handed Bevel
- 7/8” Set Screws
- 31/32” Set Screws
- 1-1/8” Set Screws
For Latch
- Long Box Strike For MS Replacement
- Strike Short Stainless Flat
- Standard Radius Double Door Strike
For MS Hook
- Box Strike For MS1850
For MS Flip
- Armoured Strike For MS1850

MS LOCK & DEADLATCH FACEPLATES
Type:
4710, 4513 (Measures 6-7/8” x 1”)
- Flat
- Flat
- Radius
- Left Handed Bevel
- Left Handed Bevel
- Right Handed Bevel
- Right Handed Bevel
- Radius With Weatherstrip
4720 (Measures 8” x 1-1/4”)
- Flat
- 4730, 4530 (Measures 7-13/32” x 1-1/4”)
- Flat
4900 (Measures 6-7/8” x 1”)
- Radius With Weatherstrip
MS1850 Series (Measures 6-7/8” x 1”)
- Flat
- Flat
- Radius
- Right Handed Bevel
- Radius With Weatherstrip


Keedex

Rings, Washers, Guards & Template

Glass-Aluminum-Keedex-Rings-Washers-Guards and Templates

CYLINDER GUARD RINGS & WAVE WASHER
- Hardened steel free spinning and tapered cone-shaped cylinder guard ring.
- Protects mortise & rim cylinders against wrenching.
- Durable powder coat finish.
- K24A & K24LA are packed with a stainless steel wave washer & spacing collar.
Cylinder Length - Washer & Collar - Finish
- 1” to 1-1/8” - Yes - Aluminum
- 1-1/4” to 1-3/8” - Yes - Aluminum
- 1” to 1-1/8” - No - Aluminum
- 1” to 1-1/8” - No - Duranodic
Description - Finish
- Wave Washer - Aluminum

DOUBLE ALUMINUM DOOR STILE GUARD
- For securing sets of double aluminum doors
- 12 gauge steel construction increases security and can repair doors that have already been attacked.
- Designed with a “knock out” to accommodate Adams Rite Bolt
- Baked on powder coat finish
- 7-3/4” x 1-3/4” x 1-3/4”
Finish:
- Aluminum

ALUMINUM DOOR OFFSET STILE GUARD
- For reinforcing or repairing jambs with offset hung aluminum doors.
- Non-handed guard is easy to install and includes pop rivets and carriage bolts.
- Baked on powder coat finish.
- 8” x 1-3/4” x 1-3/8”

ADAMS RITE ROUTER INSTALLATION TEMPLATE
- Make precise installations of Adams Rite 1850S, 4530, 4710, 4711 & 4900 series locks.
- For 7/8”, 31/32” & 1-1/8” backsets.
- Includes guide for Adams Rite exit indicator 4089.
- Has cutout for BBW #3925 & International FB-1200 flush bolts.
- For 1/2” router guide with a 1/4” bit.


LSDA

Aluminum-Glass Door Hardware: Bolts, Deadlatches, Deadlatch Lever
& Paddle Handles

Glass-Aluminum-LSDA-Aluminum Glass Door Hardware-Bolts-Deadlatches-Deadlatch Lever and Paddle Handles

MAXIMUM SECURITY BOLTS
- Maximum security bolt provides for excellent security even when a gap exists between the door & frame.
- Laminated bolt provides more strength than one piece design.
- Replacement for existing aluminum door flip & hook bolts.
- Case size: 7/8” x 6-13/16”
- Flip bolt: 5/8” x 1-3/8” throw for swinging doors.
- Hook bolt: 5/8” x 13/16” throw for sliding doors.
- Includes both clear & brown anodized aluminum faceplates.
- Bolt - Backset
- Hook - 1-1/8”
- Hook - 31/32”
- Flip - 1-1/8”
- Flip - 31/32”

DEADLATCHES
- Replacement for existing aluminum door latches.
- Case size: 7/8” x 6-13/16”
- Latch bolt: 5/8” x 1” x 5/8” throw.
- Deadpin prevents the latch bolt being shimmed open.
- Hold back function allows the latch to be “dogged” during store opening times.
- Simply hold latch in and turn key backwards to “dog” the latch.
- Includes both clear & brown anodized aluminum faceplates.
- Handing: “Quick Change” reversible handing - pull the latch and turn clockwise to change handing.
Backset - Hand
- 1-1/8” - Reversible
- 31/32” - Reversible

DEADLATCH LEVER HANDLES
- Works with aluminum door deadlatches such as the LSDA 4510 Series.
- Handle is designed to fit the hand and allow for minimum force to open the deadlatch.
- Reversible cam disc included.
Finish
- Aluminum
- Duranodic

DEADLATCH PADDLE HANDLES
- For aluminum door latches on both outswing and inswing doors.
- Reversible cam disc included.
- Both Push & Pull stickers included which allows for: Push to Right, Push to Left, Pull to Right or Pull to Left.
Finish
- Aluminum
- Duranodic
- Aluminum


Major MFG

Jamb Jackets, Door Brackets & Latch Emboss Tool

Glass-Aluminum-Major MFG-Jamb Jackets-Door Brackets and Latch Emboss Tools

JAMB JACKETS
- Door jamb reinforcer repairs and covers damaged and split out door jambs damaged by a break-in without the expense of replacing the whole jamb.
- Manufactured from sheet metal approximately 1/16” thick for 1-3/4” doors.
- 1-3/8” available by special order.
- Adds reinforcement to undamaged jambs for additional security.
- Designed to cover standard 1/2” rabbeted jamb.
- Finished in beige powdercoat for durability, may be repainted to match existing colour scheme.
- Recessed to accommodate T-strike except JJE model.
Length
- 24”
- 36”

HOLLOW METAL DOOR BRACKETS
LMB01
- For installing cylindrical knob locks or dead-bolts on hollow metal doors.
- Made of 12 gauge cold rolled steel.
- Supplied with adhesive template and pop rivets for convenience & accuracy.
- Center cut-out for seamed doors.
LMB02
- As above for mortise locksets.
LMB03
- For hollow metal or aluminum door & frames (set of 2).
Application:
- Cylindrical Knob & Deadbolt
- Standard Mortise Locks
- Metal, Aluminum Door & Frames

“PIT BULL” LATCH EMBOSS TOOL
- For latch installations on 18 & 20 gauge hollow metal steel doors, this tools creates a rectangular formed pocket at the edge of the door.
- A few turns with a wrench will squeeze an indentation that will accept both 1” and 1-1/8” wide by 2-1/4” high latches.
- Not for seam doors.