Lock Surgeon   Jobber   Supply

A Division of Lock Surgeon ™

Shipped Direct to You   or   In-Store Pick Up

Edmonton:
780-448-9243 Ext:4

Calgary:
403-770-5625 Ext:3

Toll Free:
1-844-448-9243 Ext:4

Door Hinges

Garage Door Parts
Back To Main Catagories

Door Hinges

Concealed Circuit, Single Acting Spring & Full Mortise Interim Hinges

Hinges-Mckinney-Concealed Circuit-Single Acting Spring and Full Mortise Interim Hinges

CONCEALED CIRCUIT ELECTRIC HINGE
- An intermediate connector which passes a constant flow of current between the source of power (jamb) and the actuated devices in the door.
- 28 gauge multi-strand wire with 12” long leeds.
- Available with 2 or 4 circuits.
- 1 Amp, 24 volts maximum each circuit continuous duty, 16.0 amps intermittent duty (pulse) for 300 milliseconds.
- Electric feature undetectable when hinge is installed.

FULL MORTISE SINGLE ACTING STANDARD WEIGHT SPRING HINGE
- Non handed hinge series has infinite adjustments with the tension being added or reduced by means of provided hex key.
- Locking screw provides tamper-resistance after the proper tension has been set.
- Nylon tee bearings for vertical and lateral loads.
- Coil spring provides closing power.
- Steel base material polished and plated.

FULL MORTISE INTERIM HINGE
-For new or retrofit installations.
- An equal amount is trimmed from the top and bottom of the leaf.
- Interim hinges are supplied with a no hole bottom plug and the pin is held in place by an NRP set screw which allows the hinge to be reversible.
- Steel base material.


Door Hinges

Half Surface Plain Bearing & Full Mortise Bearing Hinges

Hinges-Mckinney-Half Surface Plain Bearing and Full Mortise Bearing Hinges

FIVE KNUCKLE STANDARD WEIGHT SERIES HALF SURFACE PLAIN BEARING HINGE
- Recommended for use on minimum frequency and/or light weight wood or stock hollow metal doors in residences, apartments or other very low frequency doors in commercial construction.
- Surface mounted on door, mortised on frame.
- Steel base material polished and plated.

FIVE KNUCKLE STANDARD WEIGHT SERIES FULL MORTISE STEEL BEARING HINGE
- Bearing hinge.
- Steel based polished and plated.
- Recommended for standard weight doors or doors with closing devices.
- NRP: Non-removable pin prevents removal of hinge pin when door closed.

FIVE KNUCKLE STANDARD WEIGHT SERIES FULL MORTISE BEARING HINGE
- Recommended for standard weight, medium frequency doors, or doors with closing devices.
- Steel base polished and plated.
- NRP: Non-removable pin prevents removal of hinge pin when door closed.

FIVE KNUCKLE HEAVY WEIGHT SERIES FULL MORTISE BEARING HINGE
- Stainless steel base polished and brushed chrome plated.
- Recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other public buildings where heavy traffic is experienced.
- NRP: Non-removable pin prevents removal of hinge pin when door closed.


Door Hinges

Continuous Aluminum Hinges & Thresholds

Hinges-Pemko-Continuous Aluminum Hinges and Thresholds

FULL SURFACE CENTRE PIVOT
- Designed mainly for retrofit work and is applied to the exposed surfaces of the door and frame.
- Easily replace butt hinges since no door or frame adjustments are necessary and are more versatile with restricted frame faces.
- Door clearances: Frame side 0” to 1/8”, latch side 1/8”, top side 1/8”.
- Use where frame face clearance is less than 1-1/2”.
-Duty:
Standard - Heavy.

HALF SURFACE
- Designed mainly for retrofit work, and is applied to the exposed surface of the door and the frame rabbet.
- Designed for use with hollow metal frames, where the inset conforms to S.D. I. specifications.
- Allows for adjustments in order to properly align edge of the door to the frame.
- Door Clearances: Latch side 1/8”, frame side 1/8”, top side 1/8”.
Duty:
Heavy

THRESHOLDS
- Mill finish aluminum.
- Symmetrical shapes designed to span a given area, usually under a door.
- Saddle thresholds are supplied predrilled, with #10-24 Phillips, flat head machine screws of appropriate length.
177AV
- For vertical rod exit device.
Type - Height - Width:
36” Length
- Bumper with Vinyl 1/2” 1-1/2”.
- Standard 1/2” 4”.
- Standard 1/2” 5”.
- Standard 1/2” 6”.
- Latching with Vinyl 7/8” 5”.
- Low Profile 1/4” 6”.
72” Length
- Standard 1/2” 4”.
- Standard 1/2” 5”.
- Standard 1/2” 6”.
- Latching with Vinyl 7/8” 5”.
- Low Profile 1/4” 6”.
- Standard 1/2” 8”.